Why cranking pressure causes 'fingers' on your spray pattern
The viscosity of your paint and the shape of the tungsten cat-eye orifice decide whether your fan lays flat or splits into two heavy tracks.
Fingers (or "tails") happen when fluid pressure at the tip is below the shear threshold for your paint's thickness—or when the tungsten orifice has worn oval so the edges no longer break into droplets. Turning up pressure only until the tails vanish on cardboard (or switching to a green pre-orifice FFLP tip) fixes 95% of it.
Airless paint sprayers don't use compressed air to break paint into a mist. Instead, a piston pump compresses liquid paint to between 1,100 and 3,000 PSI and forces it through a tiny cat-eye slot carved in tungsten carbide. When that high-speed sheet of paint hits the open air, aerodynamic drag tears the sheet into millions of droplets.
Because the cat-eye slot is curved—wider in the center and pinched at the top and bottom corners—fluid moving through the outer edges travels slightly slower than fluid in the center of the fan. When your pressure is too low for the paint's viscosity, surface tension pulls those slower outer edges together into two thick streams that land on the wall as parallel railroad tracks.
Why more pressure stops helping after the fan flattens
Once the outer edges shear into droplets, adding another 1,000 PSI only accelerates tip erosion and fills the room with dry overspray.
How pre-orifice (FFLP) tips cut required pressure in half
In a traditional black airless tip, paint hits a single tungsten restriction at full pump pressure. If you lower the pressure dial to 1,200 PSI to gain more control on kitchen cabinets, the fluid exits too slowly to shear cleanly and tails appear immediately.
Green Fine Finish Low Pressure (FFLP) tips solve this by placing a second micro-chamber—a pre-orifice—just upstream of the exit cat-eye. Paint passes through the first restriction, tumbles in a low-pressure mixing chamber where turbulence breaks up its viscosity, and then exits the final orifice as an already-agitated sheet that atomizes cleanly at 1,100 to 1,350 PSI.
Graco spray tip size & pressure decoder chart
Common airless tip numbers compared
Double the first digit for fan width (inches at 12"); the last two digits are orifice diameter in thousandths of an inch.
| TIP CODE | FAN WIDTH | ORIFICE | TARGET PSI (FFLP / STD) | BEST COATING & SURFACE | GUN FILTER |
|---|---|---|---|---|---|
| 210 | 4 in | 0.010" | 1,100 PSI | Clear sealers, stains, narrow window trim | 100 mesh (Blue) |
| 310 | 6 in | 0.010" | 1,250 PSI | Cabinet doors, urethane enamels, 6-panel doors | 100 mesh (Blue) |
| 312 | 6 in | 0.012" | 1,350 PSI | Waterborne alkyd trim paint, bookshelves | 100 mesh (Blue) |
| 413 | 8 in | 0.013" | 1,400 / 1,800 PSI | Interior doors, wainscoting, closets | 60 or 100 mesh |
| 415 | 8 in | 0.015" | 1,500 / 1,950 PSI | Interior drywall primer & eggshell walls | 60 mesh (Black) |
| 515 | 10 in | 0.015" | 1,600 / 2,100 PSI | Living room walls, ceilings, exterior siding | 60 mesh (Black) |
| 517 | 10 in | 0.017" | 1,800 / 2,400 PSI | Heavy exterior acrylic latex, masonry block | 60 mesh (Black) |
- Start at 1,000 PSI on vertical scrap cardboard and raise pressure in 150 PSI steps until the top/bottom tracks merge.
- Hold the gun perpendicular (90°) to the surface at a steady 10–12 inches instead of arcing your wrist.
- Check tip wear by comparing your wet fan width against a tape measure—if a 515 tip sprays a 6.5-inch fan, retire it.
- Set your pump dial to 3,000 PSI "just to be safe"—high velocity causes paint to bounce out of cabinet corners.
- Add more than 5% water to 100% acrylic latex to clear tails before testing a smaller pre-orifice FFLP tip.
- Clean a clogged tungsten carbide tip with a steel paperclip or safety pin (metal scratches the cat-eye lip and creates permanent fingers).
Myth vs fact
Key terms
- Tails / Fingers
- Two heavy tracks of unatomized paint along the top and bottom edges of an airless spray fan.
- Pre-orifice (FFLP)
- A second chamber inside green RAC X tips that tumbles paint before the exit hole, allowing clean fans at 1,100–1,400 PSI.
- DFT (Mils)
- Dry Film Thickness, measured in thousandths of an inch (1 mil = 0.001"). Most cabinet enamels cure best at 1.8–2.2 mils DFT.
- Cat-Eye Orifice
- The elliptical tungsten-carbide slot at the front of an airless tip that shapes a pressurized fluid stream into a flat V-shaped sheet.
- Deadband Pressure
- The pressure drop between when an airless pump cycles off and kicks back on; lower deadband prevents fan width pulsing mid-stroke.
- Mesh Count (60 vs 100)
- The number of openings per linear inch in a strainer screen. Use 60-mesh for latex wall paint (.015"+) and 100-mesh for fine-finish tips (.010"–.012").
Frequently asked questions
Why do tails appear again after spraying 25 gallons with the same tip?
Titanium dioxide (the white pigment that gives paint its hide) is an abrasive mineral. At 2,000 PSI, it slowly grinds the elliptical cat-eye slot into a round hole. Once the slot rounds out, fluid concentrates at the edges and no amount of pressure will remove the tails.
Do green Graco FFLP tips fit into the standard black RAC V guard that came with my sprayer?
No. Green RAC X FFLP tips have a slightly thicker barrel diameter than black RAC V tips. You need the blue RAC X HandTite guard (roughly $24), which threads onto any standard 7/8-inch airless gun.
Does paint temperature affect spray pattern fingers?
Yes. Paint stored on a cold concrete garage floor (below 55°F) thickens significantly, raising surface tension at the edges of the fan. Bring cans indoors to 68–72°F overnight before spraying.
Go deeper
- Graco Inc., Airless Spray Tip Wear & Fluid Dynamics Technical Bulletin (321-042).
- MPI (Master Painters Institute) Architectural Coating Atomization Standards.
- Our own bench tests: 7 tip sizes, 3 latex/alkyd viscosities, 80 test panels at 68°F.
- Titan Tool Inc., Low-Pressure TR1 / HEA Fluid Shear & Transfer Efficiency Whitepaper.
- Sherwin-Williams Emerald Urethane Trim Enamel Product Data Sheet (PDS — Airless Tip Specs).
The Sunday Coat
One pro painting technique, one prep fix, one good read. Every Sunday.